Get 2022 Updated Free Cisco 300-410 Exam Questions & Answer [Q120-Q144]

Rate this post

Get 2022 Updated Free Cisco 300-410 Exam Questions and Answer

300-410 Dumps PDF and Test Engine Exam Questions

VPN Technologies

This part makes up 20% of the exam questions and evaluates the students’ skills in the following:

Explaining the MPLS operations, including label switching, LDP, LSP, and LSR;
Verifying and configuring DMVPN (the single hub). It also covers your understanding of HNRP, GRE/mGRE, IPsec, Spoke-to-Spoke, and Dynamic neighbor.
ExplainingMPLS Layer-3 VPN;

What are the Registration procedure of Cisco 300-410 Exam

The steps to follow for the registration for the Cisco 300-410 Exam are:

Create an account and go to exam registration website Cisco 300-410 Exam
Fill your student number and name in Application Registration form
Submission of form takes 25-35 minutes
The request is approved or denied by Cisco online support team
You will receive email with instructions on how to take the assessment (Forms this email may contain vary depending on each student’s request)

NEW QUESTION 120
Refer to the exhibit.

The OSPF routing protocol is redistributed into the BGP routing protocol, but not all the OSPF routes are distributed into BGP Which action resolves the issue?

Include the word external in the redistribute command

Use a route-map command to redistribute OSPF external routes defined in an access list

Include the word internal external in the redistribute command

Use a route-map command to redistribute OSPF external routes defined in a prefix list.

NEW QUESTION 121
Refer to the exhibit.

R2 is a route reflector, and R1 and R3 are route reflector clients. The route learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?

Route reflector setup requires full BGP mesh between the routers.

In route reflector setup only classification prefix are advertised from one client to another.

In route reflector setup only classful prefix are advertised to other clients.

R2 does not have a route to the next hop, so R2 does not advertise the prefix to the clients.

NEW QUESTION 122
Drag and drop the operations from the left onto the locations where the operations are performed on the right.

NEW QUESTION 123
Refer to the exhibit.

A company with autonomous system number AS65401 has obtained IP address block 209.165.200.224/27 fro, ARIN. The company needed more IP addresses and was assigned block 209.165.202.128/27 from ISP2. An engineer is ISP1 reports they are receiving ISP2 routes from AS65401. Which configuration onR1 resolves the issue?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

NEW QUESTION 124
Which feature drops packets if the source address is not found in the snooping table?

IPv6 Source Guard

IPv6 Destination Guard

IPv6 Prefix Guard

Binding Table Recovery

NEW QUESTION 125
Refer to the exhibit.

An engineer configured SNMP communities on the Core_SW1, but the SNMP server cannot obtain information from Core_SW1. Which configuration resolves this issue?

snmp-server group NETVIEW v2c priv read NETVIEW access 20

access-list 20 permit 10.221.10.11

access-list 20 permit 10.221.10.12

snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22

NEW QUESTION 126
Refer to the exhibit.

Why is user authentication being rejected?

The TACACS+ server expects “user” but the NT client sends “domainuser”

The TACACS+ server refuses the user because the user is set up for CHAP

The TACACS+ server is down and the user is in the local database

The TACACS+ server is down and the user is not in the local database

NEW QUESTION 127
Refer to the exhibit.

SanFrancisco and Boston routers are choosing slower links to reach each other despite the direct links being up Which configuration fixes the issue?

Option A

Option B

Option C

Option D

NEW QUESTION 128
Refer to the exhibit.

AS65510 iBGP is configured for directly connected neighbors. R4 cannot ping or traceroute network 192
168.100.0/24 Which action resolves this issue?

Configure R4 as a route reflector server and configure R1 as a route reflector client

Configure R1 as a route reflector server and configure R2 and R3 as route reflector clients

Configure R4 as a route reflector server and configure R2 and R3 as route reflector clients.

Configure R1 as a route reflector server and configure R4 as a route reflector client

NEW QUESTION 129
Refer to the exhibit.

The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

NEW QUESTION 130
Refer to the exhibit.

R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1. What action will fix the issue?

Fix route dampening configured on the router.

Replace the SFP module because it is not supported.

Fix IP Event Dampening configured on the interface.

Correct the IP SLA probe that failed.

NEW QUESTION 131

Refer to the exhibit. The network administrator has configured the Customer Edge router (AS 64511) to send only summarized routes toward ISP-1 (AS 100) and ISP-2 (AS 200).
router bgp 64511
network 172.16.20.0 mask 255.255.255.0
network 172.16.21.0 mask 255.255.255.0
network 172.16.22.0 mask 255.255.255.0
network 172.16.23.0 mask 255.255.255.0
aggregate-address 172.16.20.0 255.255.252.0
After this configuration. ISP-1 and ISP-2 continue to receive the specific routes and the summary route. Which configuration resolves the issue?

router bgp 64511
aggregate-address 172.16.20.0 255.255.252.0 summary-only

router bgp 64511
neighbor 192.168.100.1 summary-only
neighbor 192.168.200.2 summary-only

interface E 0/0
ip bgp suppress-map BLOCK_SPECIFIC
!
interface E 0/1
ip bgp suppress-map BLOCK_SPECIFIC
!
ip prefix-list PL_BLOCK_SPECIFIC permit 172.16.20.0/22 ge 24
!
route-map BLOCK_SPECIFIC permit 10
match ip address prefix-list PL_BLOCK_SPECIFIC

ip prefix-list PL_BLOCK_SPECIFIC deny 172.16.20.0/22 ge 22
ip prefix-list PL BLOCK SPECIFIC permit 172.16.20.0/22
!
route-map BLOCK_SPECIFIC permit 10
match ip address prefix-list PL_BLOCK_SPECIFIC
!
router bgp 64511
aggregate-address 172.16.20.0 255 255.252.0 suppress-map BLOCKSPECIFIC

NEW QUESTION 132
Refer to the exhibit.

R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?

R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.

Route reflector setup requires full IBGP mesh between the routers.

In route reflector setup, only classful prefixes are advertised to other clients.

In route reflector setups, prefixes are not advertised from one client to another.

NEW QUESTION 133
Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue?

Change the direction of the distribute-list command from out to in.

Remove the line with the sequence number 5 from the prefix list.

Remove the prefix keyword from the distribute-list command.

Remove the line with the sequence number 10 from the prefix list.

NEW QUESTION 134
An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration?

sudo maglev-config update

sudo maglev install config update

sudo maglev reinstall

sudo update config install

NEW QUESTION 135
Clients on ALS2 receive IPv4 and IPv6 addresses but clients on ALS1 receive only IPv4 addresses and not IPv6 addresses. Which action on DSW1 allows clients on ALS1 to receive IPv6 addresses?

Option A

Option B

Option C

Option D

NEW QUESTION 136
Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.

NEW QUESTION 137
Refer to the exhibit.

The administrator successfully logs into R1 but cannot access privileged mode commands. What should be configured to resolve the issue?

aaa authorization reverse-access

secret cisco123! at the end of the username command instead of password cisco123!

matching password on vty lines as cisco123!

enable secret or enable password commands to enter into privileged mode

NEW QUESTION 138
Refer to the exhibit.

Which command must be configured to make VRF CCNP work?

interface Loopback0
vrf forwarding CCNP

interface Loopback0
ip address 10.1.1.1 255.255.255.0

interface Loopback0
ip address 10.1.1.1 255.255.255.0
vrf forwarding CCNP

interface Loopback0
ip address 10.1.1.1 255.255.255.0
ip vrf forwarding CCNP

NEW QUESTION 139
Refer to the exhibit.

A network administrator logs into the router using TACACS+ username and password credentials, but the administrator cannot run any privileged commands Which action resolves the issue?

Configure TACACS+ synchronization with the Active Directory admin group

Configure the username from a local database

Configure full access for the username from TACACS+ server

Configure an authorized IP address for this user to access this router

NEW QUESTION 140
Refer to the exhibit.

The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

NEW QUESTION 141
Drag and drop the MPLS VPN device types from me left onto the definitions on the right.

NEW QUESTION 142
Refer to the exhibit.

What does the imp-null tag represent in the MPLS VPN cloud?

Include the EXP bit

Exclude the EXP bit

Impose the label

Pop the label

NEW QUESTION 143
Refer to the exhibit. Users report that IP addresses cannot be acquired from the DHCP server. The DHCP server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours per day.
Which action fixes the issue within the current resources?

Modify the subnet mask to the network 192.168.1.0 255.255.254.0 command in the DHCP pool

Configure the DHCP lease time to a smaller value

Configure the DHCP lease time to a bigger value

Add the network 192.168.2.0 255.255.255.0 command to the DHCP pool

NEW QUESTION 144
Refer to the exhibit.

AAA server 10.1.1.1 is configured with the default authentication and accounting settings, but the switch cannot communicate with the server Which action resolves this issue?

Match the authentication port

Match the accounting port

Correct the timeout value.

Correct the shared secret.

Verified 300-410 exam dumps Q&As with Correct 395 Questions and Answers: https://www.prepawaypdf.com/Cisco/300-410-practice-exam-dumps.html

VPN Technologies

What are the Registration procedure of Cisco 300-410 Exam

Related posts:

admin

You might also like

Leave a Reply Cancel reply