[Q203-Q224] 2025 Reliable Study Materials & Testing Engine for CWDP-305 Exam Success!

Q203. In a convention center, you have received complaints about the WLAN infrastructure. At this moment, there are only two APs in one auditorium. After analyzing the situation, you determined that there are more client devices than the infrastructure was designed for. There are only two APs to support more than 300 devices using Wi-Fi at the same time. What should you do to make the Wi-Fi work as expected?

Q204. Main Topic:ProtocolandSpectrum Analysis
Question:
What is the chip rate of 1 Mbps 802.11b?

Q205. A cable with 2.5 dB of loss is used to measure the return loss of an antenna. The measured value in-band is shown to be larger than 20 dB. What is the actual return loss of the antenna, and is it considered to be a reasonable value?
Response:

Q206. Wh.ch one of the following options is a dedicated throughput testing application, usable on both the WLAN and LAN?

Q207. What is the chip rate of 1 Mbps 802.11b?
Response:

Q208. During a validation site survey, you realize that the installers mounted some of the APs above the ceiling.
They said that this was a request from the building architect due to aesthetics constraints. During the requirements gathering, you weren’t advised about any aesthetics constraints from the main stakeholder of the project. What should you do in this case?

Q209. When deploying long-distance 802.11 bridge links (10 miles / 16 km), what parameter may be critical for improving data flow by reducing retries caused by the long distances?

Q210. Before performing a pre-deployment passive RF survey of a new deployment using survey mapping software, which of the following must be performed?

Q211. When deploying access points (APs) outdoors, which additional component needs to be used that is typically not required in most indoor office deployments?

Q212. What functions may be performed by a WIPS?(Choose all that apply.)

Q213. A North American business traveler connects to a hotel’s 2.4 GHz SSID in Europe and notices low RSSI from an AP in the room but experiences no issues with RSSI in the lobby. What is the most likely reason for the low RSSI in the room?

Q214. What differences exist between VLANs in wireless and wired domains?

Q215. Main Topic:Wireless Design Process
Question:
What are the three biggest WLAN enterprise verticals? (Choose all that apply.)

Q216. In addition to a copy of your design, which tools should you use to ensure the installation team deploys APs where you have them designed to be located?

Q217. Which document outlines the objectives, scope, and key stakeholders, serving as the official authorization to begin a WLAN design and deployment project?

Q218. You are conducting a physical site survey where heavy machinery is repaired. What is a common item required specifically for this type of survey?

Q219. Switches and APs have already been chosen by your customer. All switches support 802.3bz MultiGig interfaces and APs are 4×4:4 802.11ac wave 2 capable of using dual-5GHz and have one MultiGig interface. Some cable drops for the APs will run for more than 180.5 feet (or 55 meters). To support MultiGig, what is the best choice of cabling?

Q220. As an implementation engineer, you have just received initial design specs from a network designer for your dual-band 802.11n deployment. The network design documents prescribe the following data rate configuration for the 2.4 GHz radio:
Basic Rates: 5.5, 6, 11, 12 Mbps
Supported Rates: 9, 18, 24, 36, 48, and 54 Mbps as well as MCS 0-15
What will result from this design strategy?

Q221. Which one of the following might be detected as a source of CCI during a post-validation survey in the 5 GHz band?

Q222. Name the audience type not addressed in this chapter for HLDs.

Q223. Main Topic:ProtocolandSpectrum Analysis
Question:
How are EAP messages transported over 802.11 wireless LANs?

Q224. When performing a frame capture over the air during a voice call, you notice that frames in the downlink direction (from the AP to the client) are not being transmitted with the correct UP (User Priority) value for voice frames, but in the uplink direction (from the client to the AP), they are transmitted correctly. What is the likely cause of this issue?