2022 PrepAwayPDF HP HPE2-W09 Dumps and Exam Test Engine [Q33-Q48]

NO.33 Your task is to configure an EVPN solution for a dual-stack IPv4 and IPv6 protocol in the overlay networks. Is this statement about EVPN and IPv6 correct?
Solution: The IPv6 and IPv4 overlay networks can be encapsulated with VXLAN and transmitted through the underlay network.

NO.34 Does this correctly describe routing information advertised by a VXLAN Tunnel Endpomt (VTEP) that uses EVPN?
Solution: MAC/IP advertisement routes advertise the MAC addresses that can be reached through the VTEP.

NO.35 You are configuring Ethernet Ring Protection Switching (ERPS) on an ArubaOS-CX switch. Is this a guideline for configuring timers?
Solution: The guard interval is set in units of seconds and is used to prevent frequent topology changes due to a link going up and down.

NO.36 Is this how you should position switches in the ArubaOS-CX portfolio tor data center networks?
Solution: Deploy Aruba 83xx switches as core switches for very large three-tier data center networks.

NO.37 You plan to use multi-protocol BGP to implement dynamic VRF route leaking on an ArubaOS-CX switch.
Is this a rule for the setup?
Solution: You cannot leak multicast routes.

NO.38 Two ArubaOS-CX switches ate part of a Virtual Switching Extension (V5X) fabric. Is this a guideline for configuring the switches’ link-up delay settings?
Solution: Set the link-up delay timer based on the number of MAC forwarding, ARP, and routing table entries.

NO.39 Is this a guideline for establishing a Virtual Switching Extension (V5X) Inter-Switch Link (ISL) between two ArubaOS-CX switches?
Solution: Use the same speed on every link In the ISL.

NO.40 Does this correctly describe the ArubaOS-CX architecture?
Solution: The ArubaOS-CX time-series database helps to support network analytics and troubleshooting.

NO.41 The architect designs a spine and leaf network for a single data center that will use multiple leaf switches as Virtual Tunnel End Points (VTEP). The architect needs to select the type of Integrated Routing & Bridging (IRB) for the solution.
Is this statement about the IRB type true?
Solution: In the Asymmetric IRB egress VTEPs bridge the traffic to the destination networks.

NO.42 Refer to the exhibits.


Is this how the switch handles the traffic?
Solution: A broadcast arrives in VLAN 10 on Switch-1. Switch 1 forwards the frame on all interfaces assigned to VLAN10, except the incoming interface. It encapsulates the broadcast with VXIAN and sends it to 192.168.1.2. but not 192.168.1.3.

NO.43 Refer to the exhibit.
Refer to the exhibit.

You are adding a VLAN 30, subnet 10.0.30.0/24 to the network shown in the exhibit. (This network is simplified to just the relevant switches for this item.) This subnet belongs in VRF A, and you have added a Layer 3 VLAN 30 interface attached to this VRF on Switch-1. You want to make the services in this VLAN available to devices in 10.1.20.0/24 in VRF B.
Is this part of a valid setup for meeting these requirements?
Solution: Add VRF B as the secondary VRF on VLAN interface 30.

NO.44 Is this part of a valid strategy for load sharing traffic across the links in an Ethernet Ring Protection Switching IERPS) solution?
Solution: Implement Virtual Switching Extension (VSX) on pairs of ERPS switches at the same site.

NO.45 A data center has a three-tier topology with ArubaOS-CX switches at each layer, is this a use case for implementing Virtual Switching Extension (VSX) at the core?
Solution: The aggregation layer operates at Layer 2 only, and the core provides Layer 2 and Layer 3 functions.

NO.46 Is this a use case for disabling split-recovery mode on ArubaOS-CX switches in a Virtual Switching Extension (VSX) fabric?
Solution: You are not concerned about split Drain Issues in your environment, so you want the secondary member to keep its links up if the ISL falls.

NO.47 Does this correctly describe NetEdit’s notification capabilities?
Solution: NetEdlt can send an error link to admins through ServlceNow.

NO.48 You want to use NetEdit to configure an AtubaOS-CX switch.
Is this a minimum requirement for setting up communications between the switch and NetEdit?
Solution: Enable the REST interface in read-only mode.